筑坝拦截对黑河河道沉积物粒度空间分布的影响   总被引：2，自引：1，他引：1  

王昱  连运涛  冯起  王之君  赵维俊  刘娟娟  卢世国  张昕雨 《湖泊科学》2019,31(5):1459-1467

河流沉积物对流域环境变化具有敏感响应，其粒度参数能反映沉积环境中物质来源和水动力环境.本文以黑河流域上中游为研究区域，探究河流沉积物粒度对流域环境变化的响应.从黑河上中游干流22个主要控制断面采集河床沉积物样品，采用筛分法和吸管法对沉积物样品粒度参数进行测定，并分析其空间分布规律对筑坝拦截为主的环境改变响应.研究结果表明：受梯级水库建设影响，黑河上中游泥沙粒径大小差异显著.干流库区泥沙粒径较自然河段明显减小，分选很好，呈正偏或极正偏尖锐分布，而且在库区不同沉积高度上表现出分层沉积特征；坝下游河段因遭受强烈冲刷，较自然河段泥沙粒径粗化显著，分选变差，偏态趋向极正偏，峰态尖锐化；水库回水区受水库壅水及下泄清水的双重制约，泥沙粒度参数介于自然河段和坝下游河段之间，整体分选中等，呈极正偏尖锐分布；沉积环境分析表明，上游支流河段沉积物粒度特征受泥沙供给和物源特征的影响较水动力条件显著，干流河段沉积物粒度特征主要受水动力条件控制.研究结果既符合河流上中游沉积物粒度分布规律，也反映了河流环境变化对沉积物粒度组成的影响.  相似文献   

杭州湾及其邻近海域表层沉积物的沉积环境分区及重金属污染特征分析   总被引：1，自引：0，他引：1  

柴小平  魏娜  任世军  母清林  胡序朋  杜晓琴 《海洋科学》2019,43(8):29-35

于2017年春季和2018年春季,分两个航次,在杭州湾及其邻近海域采集了表层沉积物样品,并对其粒度组成及重金属含量进行了测定。结果表明,研究区域表层沉积物的粒级组成以砂和粉砂为主,平均占比分别为38.0%和55.4%。根据粒级组成的区域分布特征,将研究区域分为长江河口现代沉积区(Ⅰ-1)、钱塘江河口现代沉积区(Ⅰ-2)、长江羽状锋面积聚区(Ⅱ-1)、长江次级锋面积聚区(Ⅱ-2)、岛屿风化影响区(Ⅲ)、残留砂混合沉积区(Ⅳ)等4大类6个亚区。通过比较不同区域重金属含量发现,总体分布趋势为Ⅱ-1区和Ⅱ-2区含量较高,Ⅰ-2区和Ⅳ区含量较低,Ⅰ-1区和Ⅳ区相对居中。单因子污染指数评价结果显示,Ⅱ-1区和Ⅱ-2区的Cu、Pb、Zn、As、Cd、Hg已呈现出污染态势,需引起关注;Cr则未呈现出污染态势。  相似文献   

Evaluation of a simple,inexpensive, in situ sampler for measuring time‐weighted average concentrations of suspended sediment in rivers and streams     

Nicholas J.C. Doriean  Peter R. Teasdale  David T. Welsh  Andrew P. Brooks  William W. Bennett 《水文研究》2019,33(5):678-686

The accurate measurement of suspended sediment (<200 μm) in aquatic environments is essential to understand and effectively manage changes to sediment, nutrient, and contaminant concentrations on both temporal and spatial scales. Commonly used sampling techniques for suspended sediment either lack the ability to accurately measure sediment concentration (e.g., passive sediment samplers) or are too expensive to deploy in sufficient number to provide landscape‐scale information (e.g., automated discrete samplers). Here, we evaluate a time‐integrated suspended sediment sampling technique, the pumped active suspended sediment (PASS) sampler, which collects a sample that can be used for the accurate measurement of time‐weighted average (TWA) suspended sediment concentration and sediment particle size distribution. The sampler was evaluated against an established passive time‐integrated suspended sediment sampling technique (i.e., Phillips sampler) and the standard discrete sampling method (i.e., manual discrete sampling). The PASS sampler collected a sample representative of TWA suspended sediment concentration and particle size distribution of a control sediment under laboratory conditions. Field application of the PASS sampler showed that it collected a representative TWA suspended sediment concentration and particle size distribution during high flow events in an urban stream. The particle size distribution of sediment collected by the PASS and Phillips samplers were comparable and the TWA suspended sediment concentration of the samples collected using the PASS and discrete sampling techniques agreed well, differing by only 4% and 6% for two different high flow events. We should note that the current configuration of the PASS sampler does not provide a flow‐weighted measurement and, therefore, is not suitable for the determination of sediment loads. The PASS sampler is a simple, inexpensive, and robust in situ sampling technique for the accurate measurement of TWA suspended sediment concentration and particle size distribution.  相似文献   

Basin‐scale methods for predicting salmonid spawning habitat via grain size and riffle spacing,tested in a California coastal drainage          下载免费PDF全文

Allison M. Pfeiffer  Noah J. Finnegan 《地球表面变化过程与地形》2017,42(6):941-955

Basin‐scale predictive geomorphic models for river characteristics, particularly grain size, can aid in salmonid habitat identification. However, these basin‐scale methods are largely untested with actual habitat usage data. Here, we develop and test an approach for predicting grain size distributions from high resolution LiDAR (Light Detection and Ranging)‐derived topographic data for a 77 km² watershed along the central California Coast. This approach improves on previous efforts in that it predicts the full grain size distribution and incorporates an empirically calibrated shear stress partitioning factor. The predicted grain size distributions are used to calculate the fraction of the bed area movable by spawning fish. We then compare the ‘movable fraction’ with 7 years of observed spawning data. We find that predicted movable fraction explains the paucity of spawning in the upper reaches of the study drainage, but does not explain variation along the mainstem. In search of another morphologic characteristic that may help explain the variation within the mainstem, we measure riffle density, a proxy for physical habitat complexity. We find that field surveys of riffle density explain 64% of the variation in spawning in these mainstem reaches, suggesting that within reaches of appropriate sized gravel, spawning density is related to riffle density. Because riffle density varies systematically with channel width, predicting riffle spacing is straightforward with LiDAR data. Taken together, these findings demonstrate the efficacy of basin‐scale spawning habitat predictions made using high‐resolution digital elevation models. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

含碳结构对龙门山断层带电导率影响的实验探索   总被引：1，自引：1，他引：0       下载免费PDF全文

陈进宇  杨晓松  陈建业 《地球物理学报》2017,60(9):3475-3492

碳是影响岩石电导率大小的一个重要因素,可能是造成龙门山断层带电导率异常的重要原因之一.为了研究不同的碳含量、矿物颗粒粒径与碳晶体结构对断层带电导率的影响,在干燥、常温、0.2~300 MPa的压力条件下实验研究了人工模拟断层泥样品(石英粉末与含碳粉末混合的样品,简称模拟样品)和采自映秀-北川断层八角庙剖面的天然断层岩样品(简称天然样品)的电导率.实验结果显示,当模拟样品中的含碳粉末连通时,电导率与碳体积率的关系符合逾渗理论模型;而含碳粉末未连通时,电导率随总孔隙度降低而指数性升高.同时模拟样品的电导率也随石英颗粒粒径的变化而发生改变.相比于模拟样品中的含碳粉末主要分布于石英颗粒支撑的孔隙中,天然样品中的碳则主要以碳膜的形式赋存在颗粒边缘,导致碳体积率相同的条件下,模拟样品的电导率小于天然样品.此外,天然样品的电导率(9×10~(-4)S·m~(-1))也要小于野外大地电磁探测的结果(0.03~0.1 S·m~(-1)).在今后的实验中还需要考虑在动态摩擦条件下对含有完整含碳结构的天然样品进行电导率的实验研究.  相似文献   

Depth of closure: New calculation method based on sediment data     

Luis Aragonés  Jose Ignacio Pagán  Isabel López  José C.Serra 《国际泥沙研究》2018,33(2):198-207

Obtaining depth of closure (DoC) in an accurate manner is a fundamental issue for coastal engineering, since good results for coastal structures and beach nourishment depend mainly on DoC. Currently, there are two methods for obtaining the DoC, mathematical formulations and profile surveys. However, these methods can incur important errors if one does not take into account the characteristics and morphology of the area, or if one does not have a sufficiently long time series. In this work the DoC is obtained from the break in the trend of the sediment with the depth, that is, in general with the increase of the depth a decrease in the size of the sediment takes place. However, at one point this tendency changes and the size increases, and then decreases again. When comparing the point where the minimum sediment size occurs before the increase, it is observed that the error incurred is small compared to other methods. If the Standard Deviation of Depth Change (SDDC) method is considered as the most accurate method, the error incurred by the proposed method is less than 7%. In addition, it can be seen that the dispersion of the sediment method always occurs outside the zone of bar movement. Whereas in the methods of profiles survey (using 2 cm precision profiles), sometimes the DoC is obtained within the active zone of bar movement. In addition, where the relative minimum of the median sediment size is found, and the sizes of 0.063 and 0.125 mm predominate in the composition of the sample. Therefore, this new method allows the precise location of the DoC to be obtained in a fast and simple way. Furthermore, this method has the advantage that it is not affected by the modifications that may be experienced by both the study area and the cross-shore beach profile.  相似文献   

基于一致可靠度的地震动记录样本容量确定方法研究          下载免费PDF全文

陈波  温增平 《地震工程学报》2018,40(6):1295-1305

确定地震动输入样本容量是开展结构动力地震反应分析的重要环节,目前国内外关于地震动输入样本容量的讨论往往忽略或尚难以定量考虑结构地震反应估计的可靠度水平。以一实际钢筋混凝土框架结构为例,首先分析在大样本地震动作用下结构非线性地震反应的统计特征,研究估计结构地震反应时取样本最大值和平均值的差异,然后借助于假设检验分析结构地震反应的概率分布模型,给出基于一致可靠度的地震动样本容量确定方法,并对比分析单周期点、多周期点、谱值匹配调整地震动及人工合成地震动对样本容量需求的影响,为保证在小样本地震动输入下结构地震反应估计值满足给定可靠度和容许误差提供分析方法和判断依据。本文方法适应于定量确定不同结构类型和不同地震强度水平下的地震动样本容量需求,对建筑结构抗震性能评估及设计规范研究有一定意义。  相似文献   

From soil aggregates to riverine flocs: a laboratory experiment assessing the respective effects of soil type and flow shear stress on particles characteristics          下载免费PDF全文

T. Grangeon  I. G. Droppo  C. Legout  M. Esteves 《水文研究》2014,28(13):4141-4155

Particles eroded from hillslopes and exported to rivers are recognized to be composite particles of high internal complexity. Their architecture and composition are known to influence their transport behaviour within the water column relative to discrete particles. To‐date, hillslope erosion studies consider aggregates to be stable once they are detached from the soil matrix. However, lowland rivers and estuaries studies often suggest that particle structure and dynamics are controlled by flocculation within the water column. In order to improve the understanding of particle dynamics along the continuum from hillslopes to the lowland river environment, soil particle behaviour was tested under controlled laboratory conditions. Seven flume erosion and deposition experiments, designed to simulate a natural erosive event, and five shear cell experiments were performed using three contrasting materials: two of them were poorly developed and as such can not be considered as soils, whilst the third one was a calcareous brown soil. These experiments revealed that soil aggregates were prone to disaggregation within the water column and that flocculation may affect their size distribution during transport. Large differences in effective particle size were found between soil types during the rising limb of the bed shear stress sequence. Indeed, at the maximum applied bed shear stress, the aggregated particles median diameter was found to be three times larger for the well‐developed soil than for the two others. Differences were smaller in the falling limb, suggesting that soil aggregates underwent structural changes. However, characterization of particles strength parameters showed that these changes did not fully turn soil aggregates into flocs, but rather into hybrid soil aggregate–floc particles. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

Direct numerical simulation of flow over a slotted cylinder at low Reynolds number     

《Applied Ocean Research》2019

Direct numerical simulation was conducted to investigate the flow past a slotted cylinder at low Reynolds number (Re) of 100. The slotting of cylinder affects the boundary layer separation, vortex formation position, recirculation region length and wake width, which are determined by the type of slit. The streamwise slit (SS1), T-shaped slit (SS3) and Y-shaped slit (SS4) act as passive jets, while the transverse slit (SS2) achieves an alternate self-organized boundary layer suction and blowing. The flow rate in slits fluctuates over time due to the alternate vortex shedding and fluctuating pressure distribution around the cylinder surface. One fluctuation cycle of flow rate is caused by a pair of vortices shedding for SS2, SS3 and SS4, while it is created by each vortex shedding for SS1. The wall shear stress and flow impact on the slit wall partly contribute to the hydrodynamic forces acting on the slotted cylinder. Taking into account the internal wall of slit, the transverse slit plays the best role in suppressing the fluid forces with drag reduction of 1.7% and lift reduction of 17%.  相似文献   

三峡工程运用后坝下游河道泥沙输移变化规律   总被引：2，自引：2，他引：0  

郭小虎  渠庚  刘亚  刘心愿 《湖泊科学》2020,32(2):564-572

三峡工程蓄水后"清水"下泄,坝下游河段将会长期处于严重不饱和状态,水流含沙量沿程恢复将会引起坝下游长距离冲刷,本文根据三峡工程蓄水前、后的实测资料分析了坝下游河道泥沙输移变化规律,探索不同粒径组沙量沿程恢复对河床冲刷的影响,得到以下结论:在蓄水初期d≤0.031 mm沙量恢复主要受河床补给与江湖入汇共同的影响,随着水库下泄该粒径组沙量递减,使得各站该粒径组年均输沙量均远小于蓄水前的水平,沙量恢复仍主要受河床补给与江湖入汇的影响,这是造成坝下游河道发生长距离冲刷的主要原因之一;在蓄水初期0.031 mmd≤0.125 mm沙量恢复主要受河床补给的影响,但江湖入汇的影响较大,随着河床补给量逐渐减少,各站该粒径组年均输沙量均小于蓄水前的水平,沙量恢复仍主要受河床补给的影响,江湖入汇的影响逐渐减小,这也是坝下游河道发生长距离冲刷的主要原因之一; d0.125 mm沙量恢复主要受河床补给的影响,蓄水初期该粒径组沙量在宜昌监利河段沿程恢复速率较快,且在监利站达到蓄水前的水平,随着时间推移,在宜昌监利河段沿程恢复且速率仍较快,在监利站达到最大值,其数值逐渐小于蓄水前的水平,这是造成坝下游河道冲刷重点集中在宜昌监利河段的主要原因.  相似文献